R&D
R&D System
Performance Test
Item | Rotating Test Machine | |||||
---|---|---|---|---|---|---|
High temp | High Torque | Heat Cycle | High RPM | Muddy Water | ||
BW test | Hot Temp | Hot Temp | Cold Temp | Hot Temp | Slurry / Cold water | |
Test machine | ||||||
Capability | Head Q’ty : 4 Temp : Max.180℃ RPM : 9,000rpm Pressure : 5Bar Eccentricity : 2mmT.I.R |
Head Q’ty : 4 Temp : Max.180℃ RPM : 9,000rpm Pressure : 5Bar Eccentricity : 2mmT.I.R Torque : 10N·m |
Head Q’ty : 2 Temp : -40~180℃ RPM : 9,500rpm Pressure : 5Bar Eccentricity : 2mmT.I.R |
Head Q’ty : 2 Temp : Max.180℃ RPM : 18,000rpm Pressure : 5Bar Eccentricity : 2mmT.I.R |
Head Q’ty : 4 Temp : -40~150℃ RPM : 4,000rpm Pressure : 5Bar Eccentricity : 2mmT.I.R |
|
contents | Measure wear, oil, or radius through rotary motion | Measure wear, leakage, and absence through rotary motion of the high torque turning lever | Measure wear, oil, or radius through rotary motion | Measure wear, oil leakage, and no leaks through the rotary motion of a turning wheel for high RPM | Durability test of oil seal muddy water |
Item | Rotating Test Machine | ||||
---|---|---|---|---|---|
Saline Water | Torque |
Torque |
Noise | ||
BW test | Slurry / Cold Water | Hot Temp | - | - | |
Test machine | |||||
Capability | Head Q’ty : 4 Temp : -40~180℃ RPM : 4,000rpm Pressure : 5Bar Eccentricity : 2mmT.I.R |
Head Q’ty : 1 |
Head Q’ty : 1 Temp : Max.150℃ RPM : 6,000rpm Pressure : 5Bar Eccentricity : 2mmT.I.R Torque : 700N·m |
Head Q’ty : 6 Temp : 150℃ RPM : 0~200pm Pressure : 140Bar |
|
contents | Durability test of oil seal in muddy water for automotive HUB bearing | Check oil seal durability and performance for low pressure power steering | Measure the rotary torque of the rotary oil seal | Durability and noise verification test of oil seal for power steering low pressure |
Sortation | Reciprocation Machine | ||||||
---|---|---|---|---|---|---|---|
Friction | Assembly | valve Stem | RST | Dynamic | High Pressure | ||
BW test | - | - | - | - | - | - | |
Test machine | |||||||
Capability | Head Q’ty : 1 Temp : -40~150℃ Press force : Max1,000kgf Velocity : 5HzBar Stroke : ±75 |
Head Q’ty : 1 Press force : Max3,000kgf Velocity : 2,000mm/min |
Head Q’ty : 1 Temp : Max150℃ |
Head Q’ty : 1 Temp : -50~150℃ Press force : 50KN Stroke : ±75 |
Head Q’ty : 1 Temp : -129~200℃ Press force : 10KN Velocity : 0.01~1,000Hz |
Head Q’ty : 1 Temp : -40~150℃ Stroke : ±80 |
|
contents | Measure wear, oil, or radius through reciprocating motion | Measurement of the Pressure and the Separation force of Oil Seals | Oil leak check and durability test of valve stem seal | Measure wear, oil, or radius through reciprocating motion | Measure the vibration characteristics of the product and the specimen | Check the durability and performance of oil seal for power steering high pressure |
Sortation | Internal Pressure Test Machine | ||||||
---|---|---|---|---|---|---|---|
LOP | Unit | RCV | BPS | Negative Pressure | BPS | ||
BW test | |||||||
Test machine | |||||||
Capability | Head Q’ty : 1 Pressure : 7Kgf/㎠ Flow rate : Max 20 ℓ/min |
Head Q’ty : 1 Pressure : Max.60kgf/cm² Flow rate : Max 20㎖/min |
Head Q’ty : 1 Pressure : -750mmHg |
Head Q’ty : 1 Pressure : Max 5Mpa Flow rate : Max 20 ℓ/min Temp : Max 180°C |
Head Q’ty : 1 Pressure : Max 760mmhg |
Head Q’ty : 1 Pressure : Max.50kgf/cm² Temp : Max 180°C |
|
contents | Measurement of the seal pressure of oil seal LIP | Durability and leakage test of seals under pressure after assembling seal into JIG | Check durability at vacuum pressure cycle | Durability and leakage test of seals under pressure after assembling seal into JIG | Check oil seals for internal compression | Durability and leakage test of seals under different pressures after assembling the seal into JIG |
Sortation | Environmental Test Machine | |||||
---|---|---|---|---|---|---|
Heat Cycle Chamber | Salt Spray | High Temp Soaking | Low Temp Soaking | Heat Chamber | ||
BW test | - | - | - | - | - | |
Test machine | ||||||
Capability | Head Q’ty : 1 Temp : -50 ~ 180°C |
Head Q’ty : 1 Temp : 25 ~ 35°C |
Head Q’ty : 1 Temp : 25 ~ 200°C |
Head Q’ty : 1 Temp : -50 ~ 25°C |
Head Q’ty : 4 Temp : Max 270°C |
|
contents | Test for changes in high/low temperatures | Check whether seal rust occurs or not | Test for changes in high temperature | Test for changes in low temperature | Test for changes in high temperature |
Material Test
Itemc | Material Test Machine | ||
---|---|---|---|
FT-IR | TGA | DSC | |
Test machine | |||
Capability | Measured Infrared Range 500 ~ 4000 Cm^-1 Wae number |
Temperature : ~ 1000 ℃ Environment of measurement : Oxygen or nitrogen |
mechanical cooling method : - 70 ℃ to 400 ℃ Liquid nitrogen cooling system : - 170 ℃ to 500 ℃ |
contents | An Analysis of Raw, Secondary and Mixed Rubber Components Using Mid-Band Infrared | Analysis of Weight and Thermal Stability of vulcanized Rubber with Temperature Changes | Measure the heat changes to analyze glass transition temperature, melting point, boiling point, temperature time of crystallization, and heat response |
Item | Material Test Machine | ||
---|---|---|---|
IRHD | UTM | Rheometer | |
Test machine | |||
Capability | Longitude : 30 ~ 99 Hs | Measurement load : Less than 200 kgf Measured speed : 1,000 mm/min 이하 |
Temperature : 25℃ ~ 200℃ |
contents | Measurement of the vulcanized rubber test specimen and product hardness | Tensile Strength and elongation of vulcanized rubber | Measurement of vulcanization properties of mixed-rubber |
Item | Material Test Machine | ||
---|---|---|---|
A hydrometer | Wear-out Tester | Ozone Tester | |
Test machine | |||
Capability | Measurable weight : 0.01 ~ 200g | Friction ratio RPM : 100 rpm | Temperature : 25℃ ~ 100℃
Ozone concentration : 0 ~ 80 pphm |
contents | Measurement of the specific gravity of vulcanized rubber | Wear test of mixed-rubber rubber | Measurement of Aging of Insular Rubber |
Item | Material Test Machine | ||
---|---|---|---|
Heat resisting and aging Tester | Low Temperature Recovery Tester (tr-10) | Specimen Cutter | |
Test machine | |||
Capability | Temperature : 25℃ ~ 200℃ | Temperature : -75℃ ~ 20℃ | For production of test specimen |
contents | Oil proof tester | Measurement of cold recovery properties of rubber | Shapes for tests: Tearing, tr-10 and dumbbell type test specimen |