R&D
研究開発 システム
性能試験
Item | Rotating test machine | |||||
---|---|---|---|---|---|---|
High temp | High Torque | Heat cycle | High RPM | Muddy water | ||
BW test | Hot Temp | Hot Temp | Cold Temp | Hot Temp | Slurry / Cold water | |
Test machine | ||||||
Capability | Head Q’ty : 4 Temp : Max.180℃ RPM : 9,000rpm Pressure : 5Bar Eccentricity : 2mmT.I.R |
Head Q’ty : 4 Temp : Max.180℃ RPM : 9,000rpm Pressure : 5Bar Eccentricity : 2mmT.I.R Torque : 10N·m |
Head Q’ty : 2 Temp : -40~180℃ RPM : 9,500rpm Pressure : 5Bar Eccentricity : 2mmT.I.R |
Head Q’ty : 2 Temp : Max.180℃ RPM : 18,000rpm Pressure : 5Bar Eccentricity : 2mmT.I.R |
Head Q’ty : 4 Temp : -40~150℃ RPM : 4,000rpm Pressure : 5Bar Eccentricity : 2mmT.I.R |
|
contents | 回転運動を通して 磨耗及び漏れの 有無を測定 |
高トルク用回転シール の回転運動を通して 磨耗及び漏れの 有無を測定 |
回転運動を通して 磨耗及び漏れの 有無を測定 |
高RPM用の回転シール の回転運動を通して 磨耗及び漏れ の有無を測定 |
オイルシールの 泥水での耐久試験 |
Item | Rotating test machine | ||||
---|---|---|---|---|---|
Saline water | Torque |
Torque |
Noise | ||
BW test | Slurry / Cold water | Hot Temp | - | - | |
Test machine | |||||
Capability | Head Q’ty : 4 Temp : -40~180℃ RPM : 4,000rpm Pressure : 5Bar Eccentricity : 2mmT.I.R |
Head Q’ty : 1 |
Head Q’ty : 1 Temp : Max.150℃ RPM : 6,000rpm Pressure : 5Bar Eccentricity : 2mmT.I.R Torque : 700N·m |
Head Q’ty : 6 Temp : 150℃ RPM : 0~200pm Pressure : 140Bar |
|
contents | 自動車のハブベアリング オイルシールの 泥水での耐久試験 |
パワーステアリングの 低圧用オイルシールの 耐久性及び性能確認 |
回転用シールの 回転トルク測定 |
パワーステアリング 低圧用オイルシールの 耐久性及び騒音確認試験 |
区分 | Reciprocation machine | ||||||
---|---|---|---|---|---|---|---|
Friction | Assembly | valve stem | RST | Dynamic | High pressure | ||
BW test | - | - | - | - | - | - | |
Test machine | |||||||
Capability | Head Q’ty : 1 Temp : -40~150℃ Press force : Max1,000kgf Velocity : 5HzBar Stroke : ±75 |
Head Q’ty : 1 Press force : Max3,000kgf Velocity : 2,000mm/min |
Head Q’ty : 1 Temp : Max150℃ |
Head Q’ty : 1 Temp : -50~150℃ Press force : 50KN Stroke : ±75 |
Head Q’ty : 1 Temp : -129~200℃ Press force : 10KN Velocity : 0.01~1,000Hz |
Head Q’ty : 1 Temp : -40~150℃ Stroke : ±80 |
|
contents | 往復運動を通して 磨耗及び漏れの 有無を測定 |
オイルシールの 圧入力及び離脱 力の測定 |
バルブステムシ ールの漏れ量 確認及び耐久試験 |
往復運動を通して 磨耗及び漏れの 有無を測定 |
製品及びテストピー スの振動特性の測定 |
パワーステアリン グの高圧用オイル シールの耐久性及び 性能確認 |
区分 | Internal pressure test machine | ||||||
---|---|---|---|---|---|---|---|
LOP | Unit | RCV | BPS | Negative pressure | BPS | ||
BW test | |||||||
Test machine | |||||||
Capability | Head Q’ty : 1 Pressure : 7Kgf/㎠ Flow rate : Max 20 ℓ/min |
Head Q’ty : 1 Pressure : Max.60kgf/cm² Flow rate : Max 20㎖/min |
Head Q’ty : 1 Pressure : -750mmHg |
Head Q’ty : 1 Pressure : Max 5Mpa Flow rate : Max 20 ℓ/min Temp : Max 180°C |
Head Q’ty : 1 Pressure : Max 760mmhg |
Head Q’ty : 1 Pressure : Max.50kgf/cm² Temp : Max 180°C |
|
contents | オイルシールの 密封圧を測定 |
シールをジグに組 立てした後圧力に よるシールの耐久 性及び漏れ量試験 |
真空圧力サイクル での耐久性の確認 |
シールをジグに組 立てした後圧力に よるシールの耐久 性及び漏れ量試験 |
オイルシールの 内部圧性を確認 |
シールをジグに組 立てした後圧力に よるシールの耐久 性及び漏れ量試験 |
区分 | Environmental test machine | |||||
---|---|---|---|---|---|---|
Heat cycle chamber | Salt spray | High temp soaking | Low temp soaking | Heat chamber | ||
BW test | - | - | - | - | - | |
Test machine | ||||||
Capability | Head Q’ty : 1 Temp : -50 ~ 180°C |
Head Q’ty : 1 Temp : 25 ~ 35°C |
Head Q’ty : 1 Temp : 25 ~ 200°C |
Head Q’ty : 1 Temp : -50 ~ 25°C |
Head Q’ty : 4 Temp : Max 270°C |
|
contents | 高/低温間の 環境温度に よる変化を試験 |
オイルシールの 錆発生の有無確認 |
高温環境温度に よる変化を試験 |
低温環境温度に よる変化を試験 |
高温環境温度に よる変化を試験 |
材料試験
Itemc | Material test machine | ||
---|---|---|---|
FT-IR | TGA | DSC | |
Test machine | |||
Capability | 測定赤外線範囲 500 ~ 4000 Cm^-1 Wae number |
温度:常温 ~ 1,000℃ 測定雰囲気 : 酸素又は質素 |
機械式冷却方式 : -70 ℃~400 ℃ 液体質素冷却方式 : -170 ℃ ~ 500 ℃ |
contents | 中間大域の赤外線を利用した原, 福資材及び配合ゴムの成分分析 | 温度変化による加硫ゴムの重量変化及び 熱的な安定性分析 |
熱量変化を測定して遊離転移温度、 融点、沸点、結晶化の 温度時間及び反応熱量を分析 |
Item | Material test machine | ||
---|---|---|---|
IRHD | UTM | Rheometer | |
Test machine | |||
Capability | 硬度 : 30 ~ 99 Hs | 測定 load : 200 kgf 以下 測定温度 : 1,000 mm/min 以下 |
温度 : 25℃ ~ 200℃ |
contents | 加硫ゴムのテストピース及び製品硬度測定 | 加硫ゴムの引張強度及び伸び率測定 | 配合ゴムの加硫特性を測定 |
Item | Material test machine | ||
---|---|---|---|
比重計 | 磨耗試験機 | オゾン試験機 | |
Test machine | |||
Capability | 測定可能な重量 : 0.01 ~ 200g | 磨耗輪回転速度 : 100 rpm | 温度 : 25℃ ~ 100℃ オゾン濃度 : 0 ~ 80 pphm |
contents | 加硫ゴムの比重測定 | 配合ゴムの磨耗度試験 | オゾンによる加硫ゴムの老化測定 |
Item | Material test machine | ||
---|---|---|---|
耐熱老化試験機 | 低温回復性試験機 (tr-10) | テストピース切断機 | |
Test machine | |||
Capability | 温度 : 25℃ ~ 200℃ | 温度 : -75℃ ~ 20℃ | 試験テストピース製作用 |
contents | 耐油試験機 | ゴムの低温回復特性の測定 | 切断可能形状:引裂、Tr-10及びダンベル型テストピース |