R&D
研究开发系统
性能试验
Item | Rotating test machine | |||||
---|---|---|---|---|---|---|
High temp | High Torque | Heat cycle | High RPM | Muddy water | ||
BW test | Hot Temp | Hot Temp | Cold Temp | Hot Temp | Slurry / Cold water | |
Test machine | ||||||
Capability | Head Q’ty : 4 Temp : Max.180℃ RPM : 9,000rpm Pressure : 5Bar Eccentricity : 2mmT.I.R |
Head Q’ty : 4 Temp : Max.180℃ RPM : 9,000rpm Pressure : 5Bar Eccentricity : 2mmT.I.R Torque : 10N·m |
Head Q’ty : 2 Temp : -40~180℃ RPM : 9,500rpm Pressure : 5Bar Eccentricity : 2mmT.I.R |
Head Q’ty : 2 Temp : Max.180℃ RPM : 18,000rpm Pressure : 5Bar Eccentricity : 2mmT.I.R |
Head Q’ty : 4 Temp : -40~150℃ RPM : 4,000rpm Pressure : 5Bar Eccentricity : 2mmT.I.R |
|
contents | 测试旋转运动造成 的磨损和漏油情况 |
测试旋转运动对高扭矩 油封的磨损和漏油情况 |
测试旋转运动造成 的磨损和漏油情况 |
测试旋转运动对高 转速油封造成的磨 损和漏油情况 |
油封在浑水中 的耐久性能试验 |
Item | Rotating test machine | ||||
---|---|---|---|---|---|
Saline water | Torque |
Torque |
Noise | ||
BW test | Slurry / Cold water | Hot Temp | - | - | |
Test machine | |||||
Capability | Head Q’ty : 4 Temp : -40~180℃ RPM : 4,000rpm Pressure : 5Bar Eccentricity : 2mmT.I.R |
Head Q’ty : 1 |
Head Q’ty : 1 Temp : Max.150℃ RPM : 6,000rpm Pressure : 5Bar Eccentricity : 2mmT.I.R Torque : 700N·m |
Head Q’ty : 6 Temp : 150℃ RPM : 0~200pm Pressure : 140Bar |
|
contents | 汽车轮毂轴承油封在 浑水中的耐久性能试验 |
确认转向助力低 压油封的耐久性能 |
旋转油封的旋转扭矩测试 | 转向助力低压油封的 耐久性能以及噪音确认 |
区分 | Reciprocation machine | ||||||
---|---|---|---|---|---|---|---|
Friction | Assembly | valve stem | RST | Dynamic | High pressure | ||
BW test | - | - | - | - | - | - | |
Test machine | |||||||
Capability | Head Q’ty : 1 Temp : -40~150℃ Press force : Max1,000kgf Velocity : 5HzBar Stroke : ±75 |
Head Q’ty : 1 Press force : Max3,000kgf Velocity : 2,000mm/min |
Head Q’ty : 1 Temp : Max150℃ |
Head Q’ty : 1 Temp : -50~150℃ Press force : 50KN Stroke : ±75 |
Head Q’ty : 1 Temp : -129~200℃ Press force : 10KN Velocity : 0.01~1,000Hz |
Head Q’ty : 1 Temp : -40~150℃ Stroke : ±80 |
|
contents | 测试往复运动造成 的磨损和漏油情况 |
油封的拆,装力测试 | 阀门系统的漏油量确 认以及耐久性能试验 |
测试往复运动造成 的磨损和漏油情况 |
产品以及试片 震动特性测试 |
转向助力高压油 封的耐久性能确认 |
区分 | Internal pressure test machine | ||||||
---|---|---|---|---|---|---|---|
LOP | Unit | RCV | BPS | Negative pressure | BPS | ||
BW test | |||||||
Test machine | |||||||
Capability | Head Q’ty : 1 Pressure : 7Kgf/㎠ Flow rate : Max 20 ℓ/min |
Head Q’ty : 1 Pressure : Max.60kgf/cm² Flow rate : Max 20㎖/min |
Head Q’ty : 1 Pressure : -750mmHg |
Head Q’ty : 1 Pressure : Max 5Mpa Flow rate : Max 20 ℓ/min Temp : Max 180°C |
Head Q’ty : 1 Pressure : Max 760mmhg |
Head Q’ty : 1 Pressure : Max.50kgf/cm² Temp : Max 180°C |
|
contents | 油封混口的密 封压力测试 |
油封和模具组装后 测试不同压力下油 封的耐久性和漏 油量 |
确认真空压力循环 状态下的耐久性能 |
油封和模具组装后 测试不同压力下油 封的耐久性和漏 油量 |
油封的耐负压性能 确认 |
油封和模具组装后 测试不同压力下油 封的耐久性和漏 油量 |
区分 | Environmental test machine | |||||
---|---|---|---|---|---|---|
Heat cycle chamber | Salt spray | High temp soaking | Low temp soaking | Heat chamber | ||
BW test | - | - | - | - | - | |
Test machine | ||||||
Capability | Head Q’ty : 1 Temp : -50 ~ 180°C |
Head Q’ty : 1 Temp : 25 ~ 35°C |
Head Q’ty : 1 Temp : 25 ~ 200°C |
Head Q’ty : 1 Temp : -50 ~ 25°C |
Head Q’ty : 4 Temp : Max 270°C |
|
contents | 高/低温环境温度下试验 | 确认油封有无生锈情况 | 高温环境下的变化试验 | 低温环境下的变化试验 | 高温环境下的变化实验 |
材料试验
Itemc | Material test machine | ||
---|---|---|---|
FT-IR | TGA | DSC | |
Test machine | |||
Capability | 测试红外线范围 500 ~ 4000 Cm^-1 Wae number |
温度:常温~1000度C 测试环境:氧 or or 氮机 |
械式冷却方式: -70~400°C 液氮冷却方式: -170°C~500°C |
contents | 分析使用中间红外线的原材料 或附属材料以及调配橡胶的成分 |
分析温度变化对加硫橡胶 的重量和安全性的影响 |
通过测试热量变化分析玻璃态转变温度, 熔点,费电,结晶化的温 度时间以及反映热量 |
Item | Material test machine | ||
---|---|---|---|
IRHD | UTM | Rheometer | |
Test machine | |||
Capability | 硬度 : 30 ~ 99 Hs | 测试 load : 200 kgf 以下 测试速度 : 1,000 mm/min 以下 |
温度 : 25℃ ~ 200℃ |
contents | 加硫橡胶试验试片以及产品硬度测试 | 加硫橡胶的拉伸强度以及伸长率测试 | 测试调配橡胶的加硫特征 |
Item | Material test machine | ||
---|---|---|---|
比重计 | 磨损试验机 | 臭氧试验机 | |
Test machine | |||
Capability | 可测试重量 : 0.01 ~ 200g | 磨损率旋转速度 : 100 rpm | 温度 : 25℃ ~ 100℃
臭氧浓度 : 0 ~ 80 pphm |
contents | 加硫橡胶的比重测试 | 调配橡胶的磨损度试验 | 加硫橡胶臭氧老化测试 |
Item | Material test machine | ||
---|---|---|---|
耐热老化试验机 | 低温恢复性能试验机 (tr-10) | 试片切断机 | |
Test machine | |||
Capability | 温度 : 25℃ ~ 200℃ | 温度 : -75℃ ~ 20℃ | 试验试片制作用 |
contents | 耐油试验机 | 橡胶低温旋转特性测试 | 可切断外形:抗撕性能, tr-10以及哑铃型试验试片 |